Wiper seals factory manufacturer 2024
Excellent scraper seals factory: At the heart of why a mechanical seal works lies the rotating and stationary seal faces. Seal faces are lapped so flat it is impossible for a liquid or gas to flow through them. This allows for a shaft to spin, while a seal is being maintained mechanically. What determines the amount of time a seal will last is selecting the right seal material combination for the application. Hard seal faces for abrasive service, Carbon Vs. Ceramic for simple water (or anti-freeze in the case of automotive applications). Carbon Vs. Silicon Carbide for most applications to reduce energy consumption and provide long life. For critical applications double mechanical seals are usually recommended. See additional details at https://www.dmsseals.com/rod-seals.
The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
Supplied in rolls or open loops. The open ring can be directly installed and used, but it must be cut when the roll is used, and the cutting length must be calculated in advance: there can only be one opening, the opening form is an oblique 45° opening, and the opening distance is about 3-15mm, or the diameter of the guide ring 3-5% of . Under normal circumstances, the openings are oblique openings. Straight openings or zigzag openings are rare and have specific uses and purposes. There are two purposes for the opening. The first is to facilitate installation. If it is not opened, it is an integral ring, which is difficult to install or impossible to install, so it must be opened. Secondly, the opening and a certain opening distance are reserved to facilitate the automatic coordination of volume changes. Otherwise, the movement may be stuck or the moving parts may be pulled due to the excessive expansion of the guide belt under certain conditions. Coiled ones are relatively cheap, and the same coil can be used to make guide rings of different sizes. Discover even more info at https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.
Due to the volume and weight limitations of the system, it is impossible to install an ideal filtration and cooling system. High temperature, high pressure, and high speed cause the hydraulic oil to deteriorate easily, and the mechanical parts are also prone to erosion and stains. There are many stains and impurities in hydraulic oil, but it cannot be thoroughly filtered, which is the aspect of endogenous stains. All kinds of dust in the working environment may be very large, and it will inevitably enter the hydraulic system in multiple ways, causing oil pollution, which is an external stain. Therefore, the sealing system is required to be resistant to stains.
The O-ring of DMS SEALS is often used in hydraulic and pneumatic transmission systems and has wide applications. It can be used for both static and reciprocating seals. Moreover, it can also be used in rotary sealing systems. The O-ring can be installed in a groove with a rectangular cross section on the outer or inner circle, achieving a good sealing effect. It has many advantages compared with other types of sealing rings. Its compact structure makes it easy to assemble and disassemble. Moreover, its dynamic frictional resistance is relatively small, and a single piece of O-ring can achieve sealing performance in both directions.