Shop online MIG welders and MIG welders online store

Best welding tips: how to become a better welder and how to choose the top welding equipment. The arc is shaped like a cone, with the tip at the electrode and the base on the metal being welded. The closer the electrode is held to the metal, the smaller the base of the cone — but as you pull the electrode farther away, the base (and puddle) gets larger. If the puddle gets too large, gravity will simply pull it away from the base metal, leaving a hole. This is why thin-gauge metals are especially challenging for beginners. Perhaps the most important skill needed for TIG welding is moving the torch in a controlled manner, with steady forward movement, while keeping the gap between the tip of the electrode and the base metal consistently small — usually in the range of 1/8 inch to 3/16 inch. It requires a lot of practice to precisely control the arc length, keeping it as short as you can without allowing the electrode to touch the base metal or filler rod.

Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.

A few tips about welding equipment, MIG and TIG welders, plasma cutters. When appearance counts, TIG welding creates a high quality, clean weld that is far less likely to distort the metal by using a nonconsumable tungsten electrode. There is no need to worry about splatter because it only uses the necessary amount of filler metal needed in the welding puddle, making for the highest quality weld in every respect. However, TIG is fairly specialized and requires a good deal of training in order to master it-so make sure any TIG welder purchase is paired with a plan to take welding classes. Instead of the point and shoot simplicity of MIG welding, TIG requires the use of a foot pedal to regulate the welding process. A filler rod that is separate from the torch that must be fed in gradually. Many professional welders prefer TIG because it can weld a wide variety of metals and because of the versatility of argon gas used during TIG welding. There is no slag to block the view of the weld puddle. Argon gas can weld any metal at any thickness with TIG welding, and therefore there is no need to change the gas depending on the project.

Welding faster may sound appealing, but aside from practice, there are few shortcuts when creating a strong weld. In fact, unless a situation calls for a fast-moving weld, there’s a good chance that slow and steady is the way to go. An online search for ways to weld faster, will yield either descriptions of the ways automated welding has increased welding speed or press releases from companies who claim their gas or electrode holds the key to improving welding speed. In other words, it can seem like spending a lot of money is the only way to weld faster. However, for those looking for some ways to save time on their welding projects, there are some ways to weld faster for certain projects. While it’s not always a good idea to find a way to weld faster, there are situations when welding faster may produce a better product or a few simple changes can speed up the time on task. Read extra info on MIG welders.

Put a vent hole in anything you weld that will be sealed up completely: Put a vent hole in anything you weld that will be sealed up completely or air will heat up and expand and blow away your shielding gas or even blow out at the end of the weld bead. Some machined joints that are sealed on one end will not even allow you to start welding because the fit is so good that the part is air tight before you even weld. Other machined parts where a part is pressed in and bottomed out can give cracking problems because there is no where for the part to shrink. If you have to weld something that has been pressed in and bottomed out, make sure to add more filler metal than average to tacks and the final weld bead. That is to prevent the cracking that happens when you run a concave bead and the metal has nowhere to shrink.