Perfect Apoc Armory AR 15 lower parts

Aero Precision AR 15 upper parts by blackrifledepot.com? In 1956, designer Eugene Stoner presented his Armalite Model 10 design to the United States military as a possible replacement for the famous M1 Garand. Eugene Stoner was well known for being quite the designer and engineer, but will forever be known for his designs that led to the infamous AR 15. The United States Army was, at the time, searching for a new service rifle that could be chambered in 7.62 NATO which had been adopted only two years earlier. While Stoner’s AR 10 design was not eventually adopted, it did not go unnoticed and was considered by some other nations, such as Spain, and some commercial variants were eventually made. Instead of the AR 10 design, the United States military instead went with the Springfield M14. At the time, they felt this rifle was superior for many reasons, such as reliability, a proven track record on the design, and build quality. Unfortunately, this gun was heavy and many argued that more and more modern firefight engagements were being fought much closer than the 600 or more yards that the 7.62 NATO was originally intended for.

Keymod gets its name from the slots in the system that look like keyholes. To use a keymod handguard, all you have to do is place the mounting lug in the keyhole and slide it to the narrower end to tighten your attachment securely to the firearm. It is extremely easy to use and nowhere near as heavy or bulky as the picatinny system. Overall, this system is probably the most familiar and the longest running system of them all. If the additional weight and bulk of the picatinny platform doesn’t bother you, then there is nothing wrong with this system and it is a tried and true design. You will be pretty much guaranteed mounting for just about any accessory and won’t need to spend extra for any parts. This is probably also the cheapest option out of all of them as well.

Cut rifled barrels have long been considered the standard for the AR 15. It is by far the most popular and still to this day one of the most cost-effective ways to create barrels. A cut rifled barrel is created just like the name says: a barrel blank is inserted into a rifling machine, which resembles a large lathe. The machine then pushes a single cutter attached to a long rod through the rough rifle bore, carving out each groove of the rifling. This entire process can be very time consuming, but given the right technique and equipment, produces the most accurate AR 15 barrels that you can find. Find extra information at ar 15 parts.

This 7.5” length pistol upper assembly makes for a very fun but boisterous range gun. We run our little AR pistol with a black nitride bolt carrier group and have put just over three thousand rounds thru our personal T&E gun without a hiccup. it’s a tiny package that runs and runs, and is about as much fun as you can have with a small AR pistol. I would stress that, in our experience, this is an upper assembly I’d go with for fun above practicality. I’d also warn you that 5.56 out of a 7.5” upper assembly is quite loud. Loud may even be an understatement. I’m fairly certain, that given a choice, I’d NOT want my home defense AR sporting a 7.5” barrel. That said, the next step up is a lot more practical in that regard.

Many polymer drop-in handguards will be made of two different pieces that will fit around the barrel. They are generally fastened together by a handguard cap towards the front, and secured by a delta ring assembly in the rear. They get their name from how easy it is to install them, or to “drop-in” a new one. Installing them is super easy, and can literally be done in less than a minute. Simply pull back on the spring loaded delta ring to remove the current handguard, follow the instructions on the new one and put it in almost in reverse of removing one and there you go! Brand new handguard in no time! Most drop-in polymer handguards are offered in different lengths, in order to accommodate the varying gas system lengths of whatever AR-15 they are going on. They are generally the cheapest option, but they do have one slight disadvantage. Because of their design, they incorporate a handguard cap that is usually in contact with the forward portion of the barrel. This can possibly affect accuracy, especially if using fore grips or bipods with the handguard. This is not always the case, but something to be aware of if precision accuracy concerns you. Black Rifle Depot is a family owned and operated AR 15 Parts and AR 15 Accessories wholesale distributor based out of Bakersfield California. We offer a large variety of AR 15 Parts such as AR 15 Complete Uppers, AR 15 Barrels, AR 15 Bolt Carriers, AR 15 Handguards and AR 15 Lower Build Kits to customize your AR 15 Rifle from some of the top manufactures in the industry such as Aero Precision, Anderson Manufacturing, Faxon, Magpul Industries, and Odin works. With our continuous growing inventory and competitive prices, make Black Rifle Depot your one stop shop for AR 15 Parts and AR 15 Complete Uppers. Read more information on this website.