Category: Energy

Dry type transformer supplier factory by canwindg.com

Top rated dry type transformers producing company: What are the consequences of parallel operation of transformers that do not meet the parallel operation conditions? Parallel operation of transformers that do not meet the parallel operation conditions may lead to the following consequences: Voltage instability: Different transformers may have different electrical parameters, such as transformation ratio, resistance, inductance, etc. If these transformers with different parameters are forced to run in parallel, the overall electrical parameters after paralleling may be unstable, thereby affecting the quality of power supply. Uneven load distribution: If the transformers with uneven load distribution are forced to run in parallel, different transformers may bear different loads, thus affecting the service life and stability of the transformers. Excessive temperature rise: If different transformers are operated in parallel, their heat dissipation conditions and methods may be different, which may cause excessive temperature rise of some transformers, and may even damage the transformer. Discover extra info at dry type electrical transformers manufacturers.

Current source inverter has a higher power factor: The current source inverter has a higher power factor, which can achieve higher power factor correction, thereby reducing grid harmonic pollution. However, since a higher power factor requires larger capacitor support, a transformer with a larger capacity needs to be selected to meet the power supply requirements of the capacitor. Current source inverter needs additional power supply: The circuit of current source inverter needs additional power supply to ensure the normal operation of the current loop control. These additional power sources need sufficient capacity to support, so a transformer with a larger capacity needs to be selected to meet the power supply requirements. Therefore, the current source inverter needs a larger transformer capacity to ensure the normal operation of the intermediate inductor, support the power supply of the capacitor and meet the power supply requirements. When selecting a transformer, it needs to be selected according to the actual electrical parameters and performance requirements to ensure the normal operation and stability of the inverter.

Power Quality and Distribution Transformers – The efficiency of distribution transformer substations is significantly affected by power quality. These transformers, which are critical components of the electrical distribution system, convert high-voltage electricity into lower voltage levels suitable for end-use applications. The performance and efficiency of these transformers largely depend on the quality of power they receive. Poor power quality, characterized by voltage sags, swells, harmonics, and flicker, can lead to increased losses in power distribution transformers. These losses can be categorized into two types: core losses and copper losses. Core losses occur due to variations in the magnetic field within the transformer’s core, while copper losses occur due to the resistance of the transformer’s windings. Both these losses are exacerbated under conditions of poor power quality, leading to decreased efficiency of the transformer.

CANWIN AUTOMATICEQUIPMENT CO.,LTD is a global leading foil winding machine supplier & manufacturer with over 20 years of experiences.Ribbon foil winding machine has unique appearance, convenient operation, intuitive data display, high degree of automation, and is well received by users. This foil winding machine is widely used in oil-immersed transformer, dry transformer, special transformer and reactor production required. Foil coils are of different thicknesses copper or aluminum foil as a conductor, with wide ribbon insulation material as the insulation between layers, with narrow ribbon insulation material as the end insulation, completed winding one time, forming a coil. The inner and outer leads of the coil are welded and wrapped up at the same time.

We have provided OEM/ODM china cut to length lines and electrical machinery manufacturing service. No matter what your requirements are, our extensive know-how and experience assure you a satisfactory result. We put our most effort to offer good quality, satisfied service, competitive price, timely delivery to our valued customers. Upload your designs files & tell us important details about your project. Once you accept our quote, begin working with our team to make your ideas a reality. Your custom manufactured parts are delivered straight to your doorstep. CANWIN transform and upgrade traditional industries as an opportunity to deepen the ” one belt and one road” strategic layout, deepen cooperation with foreign markets.

Three-dimensional wound core transformer breaks through the traditional triangle plane structure, adopts three-phase symmetric vertical structure, magnetic circuit completely symmetrical three-phase core products, magnetic resistance is greatly reduced, excitation current, no-load loss, is a kind of using traditional materials, but lower operating noise, structure is more compact and efficient energy-saving oil type transformer. Its excellent performance in energy saving and energy saving and environmental protection is in line with China’s energy conservation policy.

A transformer coil winding machine is an intricate piece of machinery with an essential role in the manufacturing of transformers, combining modern technology and meticulousness to create high-quality products efficiently. The process starts with the feeding of copper wire into the machine, which passes through a line-up of calibrations guides and tensioners designed to secure alignment and prevent damage. An automated system then causes rotation, gradually looping copper wire around the transformer coil. A computerized system oversees variables such as speed, pitch control, layer count and insulation thickness for consistent turns. Moreover, for distinct transformer models or designs, these machines can be fitted with extra features such as automatic lead cutting and tapping mechanisms for increased versatility and productivity.

Want to find good electrical materials, please contact Canwin, a professional electrical material supplier with 20+ years of experiences. Electrical steel, also known as silicon steel sheet, is an important soft magnetic alloy indispensable to power, electronics and military industry, as well as the largest output of metal functional materials, mainly used as the iron core of various motors, generators and transformers. Silicon steel plate’s production process is complex, manufacturing technology is strict, foreign production technology is protected in the form of patent, as the life of the enterprise. Find more info at https://www.canwindg.com/

Transformer application of aluminum foil to make dry type transformer has small volume, light weight, good insulation performance, flame retardant, no pollution, little partial discharge, moisture proof, stable and reliable operation, low noise, low maintenance cost advantages, in the high-rise building, underground facilities, business center, residential, hotels and humid coastal areas and other applications.Want to konw composition of aluminum foil, please contact Canwin, one of the best copper foil suppliers & manufacturers in China, specialized in aluminium copper foil and transformer copper foil for over 20 years. With the rapid development of laser machines technology and equipment, it is more and more widely used in various fields. At present, most hardware products still use argon arc welding and other welding methods in production and processing.

Energy management system, which uniformly allocates and manages the wind energy, photovoltaic, power grid, battery system and distribution system of micro grid, so as to achieve energy efficiency and high-quality energy allocation. The remote cloud platform and mobile terminal can optimize the system through big data analysis, while reversing the relevant information and operation status to the users’ mobile phone. Containerized Energy Storage System is a complete, self-contained battery solution for a large-scale marine energy storage. The batteries and converters, transformer, controls, cooling and auxiliary equipment are pre-assembled in the self-contained unit. Advantages of containerized power systems: customization, scalability, stackable and cost effective.

Dry-type transformers are widely used in local lighting, high-rise buildings, airports, dock CNC machinery and equipment, etc. Simply put, dry-type transformers refer to transformers whose iron cores and windings are not impregnated with insulating oil. The relevant technical parameters of dry-type transformers include: Rated capacity (kVA): The capacity that can be delivered during continuous operation at rated voltage and rated current. Rated voltage (kV): The working voltage that a transformer can withstand during long-term operation.

Transformer core cutting line supplier from China

Top transformer core cutting line supplier factory: Power quality plays a crucial role in the performance and longevity of distribution transformer substation. Poor power quality can lead to increased losses, reduced efficiency, and shorter equipment lifespan. Therefore, effective strategies for power quality management are indispensable for the optimal operation of distribution transformers. Harmonic currents, particularly those of higher frequencies, can significantly affect the performance of transformers. These currents are produced by non-linear loads such as computers, variable speed drives, and certain types of lighting systems, causing distortions in the sinusoidal waveform of the electrical supply. See additional details on https://www.canwindg.com/products-20763.

A China slitting line produces longitudinal cuts in a master coil of steel to predetermined narrower widths. These smaller coils are then sent to downstream operations such as metal stampers, tube producers or roll forming houses that will use the material in their final product. Customized slitting line machine equipment mainly includes the following: Loading trolley, double support uncoiler, feeding device, traction leveling machine, trimming shearing machine, deviation correction feeding device, longitudinal shear line, waste edge winder, feed rack, pre separation device, tensioner, feeding roller, winding shearing machine, steering drum, rear axle, discharge trolley, winding auxiliary support, hydraulic system and electrical system, etc.

A transformer core is a static device that provides a channel for magnetic flux to flow in a transformer. The core is constructed using thin strips of silicone steel. The silicon steel sheets are electrically isolated and coupled to reduce no-load losses in the transformer.The core of a transformer is made of soft iron. Transformers are used in various fields like power generation grid, distribution sector, transmission, and electric energy consumption.

Adopt energy-saving measures: During the operation of the transformer, energy-saving measures can be adopted, such as adopting a high-efficiency cooling system, reducing the load rate of the transformer, optimizing the operation scheduling of the transformer, etc., to reduce energy loss and improve efficiency. Regular maintenance and overhaul: Regular maintenance and overhaul of transformers can maintain the normal operation and stability of transformers, thereby reducing energy loss and improving performance. Choose the appropriate transformer connection method: Different connection methods of the transformer will also affect the performance of the transformer. When choosing a transformer connection method, the optimal connection method can be selected according to actual needs and load characteristics to improve efficiency. To sum up, improving transformer efficiency can be achieved by optimizing design, selecting high-quality materials, adopting energy-saving measures, regular maintenance and overhaul, and selecting appropriate connection methods. In practical applications, various factors need to be considered comprehensively to select the most suitable method for improving performance.

Laser welding machine is an efficient and precise welding method using high energy density laser beam as a heat source. Laser welding is one of the important applications of laser material processing technology. It mainly used for welding thin wall material and low speed in the 1970 s. The welding process is thermal conduction, i.e. the laser radiation heating surface, the surface heat to the internal diffusion through heat conduction, by controlling the width of laser pulse, energy, peak power and repeating frequency, parameters such as melting of components, to form specific molten pool. Because of its unique advantages, it has been successfully used in precision welding of micro and small parts.As one of the best laser welding machine manufacturers in China, Canwin specialized in handheld laser welding machine and wholesale fiber laser welding machine making for over 20 years.

CANWIN is not just a length lines company, but also electrical equipment manufacturer. It is the legend of people who have forged their lives with faith and action. CANWIN electrical machinery equipment manufacturing deploys an innovation chain through the industrial chain.Equipment sales can provide integrated solutions; can provide OEM/ODM services to global transformer manufacturers; can provide raw material supply to transformer manufacturers. In the form of cooperation and mutual benefit, set up the transformer manufacturing center and core processing base in the Middle East, India. Dubai. Vietnam. Thailand. etc.

The loss in magnetic flux in the transformer must therefore be minimized by providing a suitable mean between the primary and secondary windings. For this purpose, silicon steel magnetic cores are usually used. By using a core type transformer, magnetic losses are reduced and a greater amount of magnetic flux is conveyed between the primary and secondary coils, thereby increasing the transformer’s overall efficiency. Electrical materials play an important role in the field of engineering technology. Various technologies should be realized through certain equipment, and the equipment needs to be made of specific materials. Without corresponding materials, even technologies and products that are feasible in principle cannot be realized. The emergence of new materials can often bring significant technological progress. Discover extra details at canwindg.com

With the development of the times, people’s demand for power supply and the reliability of power supply are increasingly high, so the smart grid has emerged accordingly.In the power system, the core and hub of the substation is the transformer.The function of the transformer is mainly to distribute and convert electric energy. The normal operation of the transformer directly affects the normal function of the substation.The intelligent operation of the transformer mainly involves the protection and status monitoring of the transformer, so as to achieve real-time monitoring of the transformer and ultimately ensure the safety and reliability of power supply.

Connection group label: According to the phase relationship between the primary and secondary windings of the transformer, the transformer windings are connected into various combinations, which are called the connection group of the windings. In order to distinguish different connection groups, the clock notation is often used, that is, the phasor of the line voltage on the high-voltage side is used as the long hand of the clock, fixed at 12, and the phasor of the line voltage on the low-voltage side is used as the short hand of the clock. The number of the short hand indicates the connection group label. For example, Dyn11 indicates that the primary winding is (triangle) connected, and the secondary winding is (star) connected with a center point, and the group number is (11) points.

What causes the transformer to make abnormal noise? Impurities or gases in the oil: Impurities or gases in the oil inside the transformer may cause unstable oil flow or air oscillations, resulting in abnormal noise. Mechanical failure: Mechanical failures inside the transformer, such as equipment failures such as transformer cooling fans or pumps, may cause abnormal sounds. Loose or leaky pipes: Loose or leaky pipes inside the transformer can cause air oscillations or unstable gas flow, which can produce unusual noises. External environmental factors: Factors such as excessive temperature of the transformer operating environment or noise interference may also cause abnormal sounds. Therefore, if the transformer makes abnormal noise, it is necessary to check and repair the transformer in time. The specific maintenance method needs to be selected according to the cause of the abnormal sound and the specific situation in order to restore the normal operation and stability of the transformer. At the same time, during the installation, operation and maintenance of the transformer, attention should be paid to environmental temperature, humidity, noise and other factors to avoid adverse effects on the transformer.

As one of the best dry type transformer manufacturers & suppliers in China, Canwin specialized in dry type power transformer manufacturing for over 20 years.Our dry transformer is widely used in local lighting, high-rise buildings, airports, terminals CNC mechanical equipment and other places, simply said dry type transformerrefers to the core and winding are not impregnated in the transformer insulation oil.There are two main types of dry type transformers: cast resin dry type transformer (CRT) and vacuum pressure impregnated transformer (VPI).

I migliori servizi del settore energetico da con LAG. POWER SRL Lucera e Gianluca Luparelli

Migliori servizi del settore energetico da con LAG. POWER SRL Lucera e Gianluca Luparelli: Servizi energetici eolici di qualità da con LAG. POWER SRL Lucera e Gianluca Luparelli: Quindi ecco il punto: nonostante tutta la loro utilità quando vivi fuori dalla rete, i generatori sono rumorosi. Interromperanno la tranquilla solitudine della tua casa off-grid immersa nei boschi, nelle montagne o in altri luoghi remoti. In effetti, sono così rumorosi che oggi la maggior parte dei produttori ora include i livelli di decibel (db) nelle loro specifiche. Considerare il livello di rumore PRIMA di acquistare un generatore per uso domestico. E considera il livello di rumore in base alla vicinanza del generatore a casa tua. E se li hai, anche nelle case dei tuoi vicini. Diversi studi come questo dell’Organizzazione Mondiale della Sanità (OMS) hanno dimostrato che le persone possono avere sintomi fisici reali diversi dalla perdita dell’udito a causa del rumore eccessivo. Vedi ancora di più informazioni su LAG. Power SRL.

Tra l’inizio del 2014 e il 2017, il prezzo delle batterie al litio stazionarie è diminuito di oltre il 40%. Questa tendenza dovrebbe continuare. Inoltre, la fine di febbraio ha visto l’introduzione di un nuovo programma di finanziamento che proseguirà fino al 2018. Questi sono buoni motivi per investire in una batteria solare. La dimensione da scegliere dipende dalla richiesta di elettricità dell’edificio e dalle dimensioni del generatore solare. Attualmente le batterie al litio costano circa 1.000 euro al kilowattora, le batterie al piombo circa dai 500 ai 600 euro (prezzi netti per i clienti finali). Tuttavia: in una residenza privata, avere un magazzino senza generatore solare ha poco senso. Questo può essere diverso per le imprese commerciali.

Azienda leader nel settore dell’energia solare con Gianluca Luparelli e LAG. POWER SRL: Sebbene l’energia solare sia certamente meno inquinante dei combustibili fossili, esistono alcuni problemi. Alcuni processi di produzione sono associati alle emissioni di gas serra. Il trifluoruro di azoto e l’esafluoruro di zolfo sono stati fatti risalire alla produzione di pannelli solari. Questi sono alcuni dei gas serra più potenti e hanno un impatto sul riscaldamento globale molte migliaia di volte maggiore rispetto al biossido di carbonio. Anche il trasporto e l’installazione di sistemi di energia solare possono causare inquinamento indirettamente.

Sebbene l’energia solare possa ancora essere raccolta durante i giorni nuvolosi e piovosi, l’efficienza del sistema solare diminuisce. I pannelli solari dipendono dalla luce solare per raccogliere efficacemente l’energia solare. Pertanto, alcuni giorni nuvolosi e piovosi possono avere un notevole effetto sul sistema energetico. Dovresti anche considerare che l’energia solare non può essere raccolta durante la notte. D’altra parte, se hai bisogno che la tua soluzione di riscaldamento dell’acqua funzioni anche di notte o durante l’inverno, i pannelli termodinamici sono un’alternativa da considerare. Scopri di più informazioni at LAG. POWER SRL e Gianluca Luparelli.

Prima di tutto: se vuoi risparmiare sui costi dell’elettricità, con o senza fotovoltaico, dovresti prima eliminare i dispositivi e gli elettrodomestici che ne consumano troppo. Questi includono dispositivi di standby, lampadine a incandescenza e scaldabagni. Minore è il consumo complessivo, maggiore sarà la parte che sarai in grado di coprire utilizzando il solare fotovoltaico.

Quality dry type electrical transformers manufacturer factory

Dry type power transformer manufacturer with Canwin: Adjustment under heavy load or short circuit conditions is not allowed: Under heavy load or short circuit conditions on the transformer, tap changer adjustment may cause arcing or excessive current, resulting in damage to the tap changer or transformer. Obey the operating procedures and safety measures: When operating the on-load pressure regulating device, you need to abide by the operating procedures and safety measures, such as wearing protective equipment and following the operating procedures to ensure safe operation. In summary, it is not allowed to operate under live conditions, frequent adjustments, heavy loads or adjustments under short-circuit conditions. When operating the on-load pressure regulating device, the operating procedures and safety measures should be followed to ensure safe and stable operation. See additional info at transformer lamination.

Why does the current source inverter need a larger transformer capacity? Current source inverter is a common type of inverter. Its control method adopts current loop control, which has the advantages of high precision and strong adaptability, and is widely used in industrial production. Due to the working characteristics of the current source inverter, a large transformer capacity is required for the following reasons: The current source inverter adopts the intermediate inductance: the current source inverter adopts the intermediate inductor, which can realize the phase difference between the output voltage and the current, so as to realize the frequency conversion control. However, since the intermediate inductor needs to withstand large current and voltage, it is necessary to select a transformer with a larger capacity to ensure the normal operation of the inductor.

Several factors can affect power quality in transmission lines. These include: Load Characteristics: Non-linear loads can generate harmonics that distort the voltage and current waveforms, affecting the power quality. Transmission Line Length: Longer transmission lines have higher impedance, which can cause voltage drops and affect power quality. Faults on the System: Short circuits, ground faults, or equipment failures can lead to voltage sags, swells, or transients, impacting power quality. Switching Operations: The switching on/off of large loads or reactive power compensation devices can cause transient overvoltages that degrade power quality. Grid Interconnections: Interconnections between different power systems can introduce disturbances, affecting the power quality.

The cut to length line is a special equipment for the production of transformer core, is our latest generation of cross shear line. This cut to length production line is used for shearing, O punching and V notch of transformer core sheet. The special point of this ctl line is that two O punch and one V notch can work at the same time to produce transformer core pieces with 3, 5, 7 steps in vertical direction and 3, 5, 7 steps in horizontal direction.

The trademark “CANWIN” has won the title of the famous trademark of the international electrotechnical association and the trademark CANWIN CNC” has been recognized as a high -end manufacturing brand in China. We has been judged as Guangdong province enterprise that strictly contracts and keeps promises” and won the honor of”excellent supplier of Chinese electrical equipment” successively. The company has a number of national patents, and won the Guangdong provincial department of science and technology major project award the first set of domestic new products award; The company is a key enterprise in the field of electric power electrical equipment manufacturing in China, and a core professional equipment supplier of state grid, China southern power grid and many listed companies in the electric power industry. Its products are exported to countries and regions in Asia, Africa, Latin America, Europe and the United States.

Oil immersed transformers are the most commonly used equipment mainly because of their simple structure and reliable operation. It has faster heat dissipation, uniform conduction, and better insulation performance than the dry-type transformer.Oil transformers are used in power distribution or electrical substations. Their transformer core and coils are immersed in oil, which cools and insulates. Oil circulates through ducts in the coil and around the coil and core assembly, moved by convection.

A transformer coil winding machine is an intricate piece of machinery with an essential role in the manufacturing of transformers, combining modern technology and meticulousness to create high-quality products efficiently. The process starts with the feeding of copper wire into the machine, which passes through a line-up of calibrations guides and tensioners designed to secure alignment and prevent damage. An automated system then causes rotation, gradually looping copper wire around the transformer coil. A computerized system oversees variables such as speed, pitch control, layer count and insulation thickness for consistent turns. Moreover, for distinct transformer models or designs, these machines can be fitted with extra features such as automatic lead cutting and tapping mechanisms for increased versatility and productivity.

The loss in magnetic flux in the transformer must therefore be minimized by providing a suitable mean between the primary and secondary windings. For this purpose, silicon steel magnetic cores are usually used. By using a core type transformer, magnetic losses are reduced and a greater amount of magnetic flux is conveyed between the primary and secondary coils, thereby increasing the transformer’s overall efficiency. Electrical materials play an important role in the field of engineering technology. Various technologies should be realized through certain equipment, and the equipment needs to be made of specific materials. Without corresponding materials, even technologies and products that are feasible in principle cannot be realized. The emergence of new materials can often bring significant technological progress. Find extra information at https://www.canwindg.com/

The metal laser cutting machine focuses the laser emitted from the laser into a laser beam with high power density through the optical path system. The laser beam irradiates the surface of the workpiece to make the workpiece reach the melting point or boiling point. At the same time, the high-pressure gas coaxial with the beam blows away the molten or gasified metal. With the movement of the relative position between the beam and the workpiece, the material will finally form a slit, so as to achieve the purpose of cutting. Laser cutting process uses invisible light beam to replace the traditional mechanical knife. It has the characteristics of high precision, fast cutting, not limited to the limitation of cutting pattern, automatic typesetting, material saving, smooth incision and low processing cost. It will gradually improve or replace the traditional metal cutting process equipment.Want to konw more about metal cutting machine, contact us, one of the most professional metal laser cutting machine manufacturers & suppliers in China.

Digital measurement – Digital measurement of transformers or other components can be conducted, and the measurement results can be called and collected from the process layer and station control layer through digital networks, thus monitoring transformers and other equipment.Status visualization – The operation status of transformers can be visualized and observed in the power grid.Smart grid or other related systems can express the status information of transformer self-detection or information interaction.

Insulation level: There are standards for insulation levels. The insulation level of a transformer with a rated high voltage of 35 kV and a rated low voltage of 10 kV is represented as LI200AC85/LI75AC35, where LI200 indicates that the transformer has a high-voltage lightning impulse withstand voltage of 200 kV, a power frequency withstand voltage of 85 kV, and a low-voltage lightning impulse withstand voltage of 75 kV, and a power frequency withstand voltage of 35 kV. The current insulation level of Aux High-Tech Co., Ltd.’s oil-immersed transformer products is LI75AC35, indicating that the transformer has a high-voltage lightning impulse withstand voltage of 75 kV and a power frequency withstand voltage of 35 kV. Because the low voltage is 400 V, it can be ignored.

Best rated turn key solar power parks constructor with Photon Mills

High quality solar power stations services with Photon Mills: Romania is undergoing a significant expansion in solar power within its broader energy transition framework, bolstered by European funding and legal reforms. This upsurge has prompted investments across the spectrum, from individual households as prosumers to utility-scale facilities, with local government units emerging as a significant segment for development up to the county level. Alongside solar, some localities are exploring geothermal energy prospects. Read more info on EU solar power stations services and discover the great investment opportunities in Romania’s solar power market.

Invest in ready to build turn key solar power stations in the European Union! Photon Mills is offering solar power stations in the sunny south of Romania. It includes land, permits and grid connections. Start of electricity production one month after start of construction. Start of electricity production one (25 MW photovoltaic power station) or two months (290 MW photovoltaic power plant) after the start of construction.

Photon Mills offers a wide range of services throughout a project’s life cycle: from production and site design optimization to operations and maintenance. Our refined services and processes provide an exceptional experience and enough flexibility to customize your solar project. We provide complete solar energy solutions and deliver high-quality, cutting-edge solar projects on time and on budget. Photon Mills, powered by industry leading experts, top engineers and marketing representatives has been trusted to build many solar projects in Romania.

Photon Mills is an expert in the development, planning and turnkey construction of solar parks. We are passionate about realising solar projects in Romania and manage the entire process from planning to commissioning of the plant. Our expertise ranges from site selection and technical implementation to the operational management of the PV plants. The maximum return on your investment and the continuous guarantee of high yields are always our focus.

In the country-specific breakdown of solar capacity additions since the onset of 2023, Germany leads the European nations with an installation of 14.1 GW of new solar capacity. Spain follows as the second-highest with 8.2 GW, with Italy (4.8 GW), Poland (4.6 GW), and the Netherlands (4.1 GW) rounding out the top five contributors. This distribution highlights the uneven yet significant strides being made across the continent in harnessing solar energy, reflecting a collective move towards renewable energy sources and a more sustainable energy future. See additional information at Photon Mills.

The renewable energy market consists of establishments primarily operating renewable electric power generation facilities. Power generation can come from a variety of sources, including solar energy, wind energy, small hydro, bioenergy, geothermal and marine. The electrical energy generated in these establishments is provided to electric power transmission systems or to electric power distribution systems. In the current energy mix of Romania, hydropower accounts for more than a third of the country’s electricity production, followed by coal (18.1%), wind power (15.9%), fossil fuels (15.1%), nuclear power (7.5%), solar energy (7.5%), and biomass related (0.8%).

In the course of project development, questions of a technical, financial and legal nature regularly arise. Thanks to our many years of know-how in project development, we can support you with all these issues, taking into account the individual requirements of the respective country and region. Photon Mills and its local partners develop your photovoltaic system throughout Europe – contact us directly and provide information on the location and size of your project.

פיתוחים בתעשיית האנרגיה המתחדשת עם גל שופרוני

חברות אנרגיה מתחדשת באיכות גבוהה של גל שופרוני היום :

חברת טראלייט מדווחת הבוקר (א’) כי זכתה בקול קורא של לשכת המדען הראשי במשרד האנרגיה במסגרת ועדת שיפוט משותפת של משרד האנרגיה ומשרד החקלאות להקים פרויקטי דו-שימוש באנרגיות מתחדשות בשטחים חקלאיים (אגרו-וולטאי) עבור 4 מתקנים בארץ בהספק כולל של כ-2.52 מגה וואט.

במסגרת המחקרים, קבוצת טראלייט תקים 4 מתקנים לייצור אנרגיה מתחדשת ותפעילם. במסגרת הפרויקטים, תבחן הדו-שימושיות בשטח החקלאי למטרות גידול של גידולים חקלאיים שונים ולשימוש של הפקת אנרגיה סולארית פוטו-וולטאית. המחקרים יערכו ביחס למספר גידולים, יפרסו באזורים גיאוגרפים אקלימיים שונים ברחבי הארץ וילוו על ידי חוקרים בעלי שם בעולם החקלאות.

חברת האנרגיה טראלייט +0.55% שהחלה להיסחר בשנה שעברה, זכתה בקול קורא של לשכת המדען הראשי במשרד האנרגיה (במסגרת ועדת שיפוט משותפת של משרד האנרגיה ומשרד החקלאות) להקים פרויקטי דו-שימוש באנרגיות מתחדשות בשטחים חקלאיים (אגרו-וולטאי) עבור 4 מתקנים בארץ בהספק כולל של כ-2.52 מגה וואט. לפי ההערכות בשוק, מדובר בהיקף כספי של מיליון שקל לשנה.

במסגרת המחקרים, יעשה שילוב של טכנולוגיות ייחודיות להגדלת תפוקת היבול ויצירת מיקרו-אקלים אופטימלי עבורם, וכן שילוב של אמצעי מדידה ובקרה מדויקים. המחקרים יבחנו את שטח הכיסוי האופטימלי של פאנלים סולריים בהיבט השפעת הפאנל על מרכיבי היבול ועל איכות הפרי, ואת ההשפעה ההדדית (צמח -פאנל) כדוגמת צינון טמפרטורת הסביבה של הפאנלים ובכך הגדלת תפוקת ייצור החשמל שלהם. כמו כן, תיבחן השפעת המתקן הסולארי על כמות המים העומדת לרשות הגידול, כדי למצוא דרכים לנצל את המתקן הסולארי לטובת שיפור כמויות המים שיעמדו לרשות הצמח, אף בהשוואה למצב בו אין מתקן סולארי מעליו.

גל שופרוני, סמנכ”ל פיתוח עסקי ורגולציה של טראלייט ציין: “השמירה על האיזון בין צרכי החקלאות של מדינת ישראל מחד והעמידה ביעדי האנרגיות המתחדשות של המדינה מנגד, הביאה אותנו לקדמת הטכנולוגיה הסולארית וממצבת את ישראל כמובילה מחקרית בתחום שהולך ותופס תאוצה בכל רחבי העולם. עם הידע שטראלייט תרכוש בישראל, בין היתר באמצעות סדרת המחקרים האלו, בכוונתנו לפתח פעילות ייחודית בחו”ל”: גל שופרוני

בחודש שעבר, טראלייט זכתה בקול קורא של משרד האנרגיה ולשכת המדען הראשי, להקמת פרויקט מיקרו-גריד ראשון מסוגו בקריית ביאליק, במסגרתו החברה תקים קירוי סולארי על גבי מגרש חניה, בשילוב עמדות טעינה לרכבים חשמליים ומתקן אגירה. הפרויקט, אשר זוכה לתמיכה בהיקף של 1.3 מיליון שקל, יכלול בשלב הראשון 500 קילו-וואט סולארי, 10 עמדות טעינה לרכבים חשמלים ואגירה בקיבולת של 2.3 מגה וואט שעה. בשלב הבא, ככל שהביקוש לעמדות הטעינה יגדל, צפוי שהפרויקט יתרחב.

רני ליפשיץ, מנכ”ל טראלייט: “אנו גאים לקחת חלק במחקר חשוב זה, תוך שאנו מזהים את המצוקה ההולכת וגדלה בה מצוי ענף החקלאות בארץ וסבורים כי פרויקטים אלו ייצרו ביטחון וודאות כאשר ייצור החשמל יאזן את תפוקת היבול ויניב פירות לכל הצדדים. אנו מעריכים כי תוצאות המחקרים יסייעו בהרחבת פעילות טראלייט בתחום הדו-שימוש, זאת בהתאם לאסטרטגיה שהתווינו. לצד פרויקטי הדגל של החברה הכוללים שני מתקנים סולאריים מהגדולים בארץ בהספק משותף של כ-600 מגה וואט, טראלייט רואה בפרויקטי דו-שימוש חשיבות רבה, על רקע השטחים המצומצמים בארץ והצורך בשימוש במשאבים קיימים כרבי תכלית”

כמו כן, גם חברת פריים אנרג’י +3% הודיעה כי ועדת השיפוט המשותפת של משרדי האנרגיה והחקלאות החליטה לקבל את בקשתה במסגרת פנייה להגשת תכניות מקדימות לדו-שימוש באנרגיות מתחדשות בשטחים חקלאיים (אגרו-וולטאי) עבור 12 מתקני חלוץ שהוגשו על-ידי אגרילייט, שמוחזקת על ידה ב-7.5%. להערכת החברה, מתקני החלוץ צפויים לייצר הכנסה של כ-5.5 מיליון שקל בשנה (וסך כולל של כ-126 מיליון שקל למשך 23 שנים).

במסגרת המחקרים, החברה תקים 4 מתקנים לייצור אנרגיה מתחדשת ותפעילם. במסגרת הפרויקטים, תבחן הדו-שימושיות בשטח החקלאי למטרות גידול של גידולים חקלאיים שונים ולשימוש של הפקת אנרגיה סולארית פוטו-וולטאית. המחקרים יערכו ביחס למספר גידולים, יפרסו באזורים גיאוגרפים אקלימיים שונים ברחבי הארץ וילוו על ידי חוקרים בעלי שם בעולם החקלאות.

במסגרת המחקרים, יעשה שילוב של טכנולוגיות להגדלת תפוקת היבול ויצירת מיקרו-אקלים אופטימלי עבורם, וכן שילוב של אמצעי מדידה ובקרה מדויקים. המחקרים יבחנו את שטח הכיסוי האופטימלי של פאנלים סולריים בהיבט השפעת הפאנל על מרכיבי היבול ועל איכות הפרי, ואת ההשפעה ההדדית (צמח -פאנל) כדוגמת צינון טמפרטורת הסביבה של הפאנלים ובכך הגדלת תפוקת ייצור החשמל שלהם.

גל שופרוני, סמנכ”ל פיתוח עסקי ורגולציה של טראלייט ציין: “השמירה על האיזון בין צרכי החקלאות של מדינת ישראל מחד והעמידה ביעדי האנרגיות המתחדשות של המדינה מנגד, הביאה אותנו לקדמת הטכנולוגיה הסולארית וממצבת את ישראל כמובילה מחקרית בתחום שהולך ותופס תאוצה בכל רחבי העולם. עם הידע שטראלייט תרכוש בישראל, בין היתר באמצעות סדרת המחקרים האלו, בכוונתנו לפתח פעילות ייחודית בחו”ל”.

בחודש שעבר, טראלייט זכתה בקול קורא של משרד האנרגיה ולשכת המדען הראשי, להקמת פרויקט מיקרו-גריד ראשון מסוגו בקריית ביאליק, במסגרתו החברה תקים קירוי סולארי על גבי מגרש חניה, בשילוב עמדות טעינה לרכבים חשמליים ומתקן אגירה. הפרויקט, אשר זוכה לתמיכה בהיקף של 1.3 מיליון שקל, יכלול בשלב הראשון 500 קילו-וואט סולארי, 10 עמדות טעינה לרכבים חשמלים ואגירה בקיבולת של 2.3 מגה וואט שעה. בשלב הבא, ככל שהביקוש לעמדות הטעינה יגדל, צפוי שהפרויקט יתרחב.

רני ליפשיץ, מנכ”ל טראלייט: “אנו מעריכים כי תוצאות המחקרים יסייעו בהרחבת פעילות טראלייט בתחום הדו-שימוש, זאת בהתאם לאסטרטגיה שהתווינו. לצד פרויקטי הדגל של החברה הכוללים שני מתקנים סולאריים מהגדולים בארץ בהספק משותף של כ-600 מגה וואט, טראלייט רואה בפרויקטי דו-שימוש חשיבות רבה, על רקע השטחים המצומצמים בארץ והצורך בשימוש במשאבים קיימים כרבי תכלית”.

ליאור אהרון, מנכ”ל פריים אנרג’י: “אנחנו שמחים על ההשקעה באגרילייט ומאמינים בצוות החברה ובמוצר שהיא מפתחת, אשר יאפשר ניצול שטחים חקלאיים לשם ייצור חשמל ירוק. ההשקעה באגרילייט מצטרפת להתמקדות של פריים אנרג’י בפרויקטים בשימוש דואלי ואגרו-וולטאי, אשר יהוו גורם משמעותי ביכולת של מדינת ישראל לעמוד ביעדי הייצור מאנרגיות מתחדשות. להשקעה המוצלחת נלווה גם שיתוף פעולה יזמי באופן שפריים אנרג’י שותפה ב-50 אחוזים בפעילות הייזום של אגרילייט, לרבות בזכייה הנוכחית. הזכייה בקול הקורא מצטרפת לזכייה הנוספת של פריים אנרג’י – זכייה בהספק של 475 מגה וואט במכרז הדו שימוש של רשות החשמל, אשר פריים אנרג’י פועלת בימים אלה לממש באמצעות פרויקטים על גגות, חממות, מאגרי מים, גדרות, מצללות, חניונים, בתי עלמין, שבילי הליכה ועוד”.